Doepfer A-100Ad5

28

5V Low-cost adapter

  • Plug adapter for +5 V / 100 mA
  • Can be used in place of a 5 V power supply
  • For Doepfer modules requiring +5 V: e.g. the A-113,190 or 191
  • Can be plugged into a free socket on the bus board
  • The current is taken from the 12 V supply
Produkt dostępny od Styczeń 2004
Numer artykułu 166503
Jednostka sprzedaży 1 szt.
Description Electronic Component
64 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Wysyłka spodziewana do dnia Wtorek, 30.04.
1

28 Oceny klientów

4.8 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

wykończenie

15 Opinie

google translate gb
Wystąpił błąd. Proszę spróbować później.
S
May the force be with you... exactly 5 volts.
Stephen662 15.07.2013
Needed this to supply 5 volts to some of the modules in my Doepfer case. Yes, some modules (usually logic modules) need 5v to work, and this is what you need.

Simply plugs into the rail that you need to supply the 5v on - if you have 5v modules all over your rack you will need to instal one on each rail as required. Job done. Works a treat.
3
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
You might not think you need this but you probably will
Anonimowy 20.01.2016
This little adaptor will allow you to run anything which requires a +5v power supply on one power rail of your modular case. I bought it because it was required for an oscillator which I purchased, but it can have many applications. My next use for it will be to power LED lights to illuminate my modular in gig situations. You simply connect the adaptor to a spare connector on the rail which you will need it, and then you have +5v power available for all the other connectors on that rail. My one reservation is that this could have been a little bit cheaper for what it does, or alternatively Doepfer could just build this provision into their modular cases as standard. After all a P9 case, for example, is not cheap and when you have spent that amount of money you kind of resent having to buy this.
0
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
A
Andrew463 06.12.2014
Tough one to rate as it's just a plug... but if you have products from Mutable Instruments and others that require 5-Volt power it's a necessity for a Doepfer rack. It couldn't be any simpler to use, just plug it in and away you go.

Again, good value too.
1
0
Zgłoś nadużycie

Zgłoś nadużycie

google translate gb
Wystąpił błąd. Proszę spróbować później.
HT
Get it for those hungry modules.
Harry Turner 02.11.2019
The Sub Harmonic Generator requires this.
wykończenie
0
0
Zgłoś nadużycie

Zgłoś nadużycie